The MovinCool Climate Pro K18 / K18e is a heavy-duty portable air conditioner built to deliver fast, reliable cooling in demanding environments. It moves high volumes of air and targets heat directly where it matters, helping maintain safe and productive workspaces.
With flexible ducting, rugged construction, and simple controls, this unit is ideal for temporary or supplemental cooling in areas where permanent HVAC isn’t practical.
Why it matters:
Heat slows productivity, stresses equipment, and creates uncomfortable conditions. The K18 solves this by delivering focused cooling exactly where you need it—without complex installation.
Key Features & Benefits
- Delivers strong cooling for large spaces and spot cooling needs
- Portable design with casters for easy relocation
- Flexible air ducts direct cool air where needed most
- Built for industrial, commercial, and event environments
- Simple controls for fast setup and operation
- Operates on standard power for jobsite flexibility
- Available in R-410A and lower-GWP R-32 refrigerant models
- Durable construction for continuous use in tough conditions
Additional Specifications
| MovinCool Climate Pro K18/K18e Owner's Manual |  |
| MovinCool Climate Pro K18/K18e Product Spec Sheet |  |
| (NOTE: 12,000 BTUs = 1 ton of cooling / 1 ton of cooling covers 400-500 sq ft) | |
| NOTE: Specifications subject to change without notice. All models feature compressor overload relay and fan motor protection. All models also feature compressor short-cycle protection, return air thermostat, automatic restart and accommodate a condensate pump kit. All models are 50 Hertz (Hz) compatible with a slight performance decrease from the specifications listed above. |
|
MovinCool Climate Pro K-18 Installation and Accessory List
All accessories are sold separately.
All accessories are sold individually unless otherwise noted.
Exhaust duct required in most cases.
1. Quick Connect Two Hole Adapter/Flange Base Plate - 481170-0480
Base Plate has two 5-inch diameter Quick Connect holes with molded flanges. Includes wire clamp and mounting screws.
(Use with #2 quick connect nozzle(s).)
2. Quick Connect Nozzle Kit - 484209-0480
5-inch diameter Quick-Connect Nozzle extends up to 2-ft in length. Includes trim ring.
(Use with #1 quick-connect adapter/flange base plate.)
3. Two Hole Base Plate - 481769-0280
Base plate has two 5-inch diameter holes to convert the airflow from factory-installed louvers to nozzles or air ducts.
4. Supply Air Flange Kit - 481170-0450
5-inch diameter flange kit includes wire clamp and mounting screws. (Used to attach the self-supported cold air duct to the two-hole base plate.)
5. Self-Supported Cold Air Duct - LA481744-0420
5-inch diameter self-supported duct extends from 6.5-ft to 10-ft in length. Provides specific, directional airflow.
6. Trim-Ring - 481851-0200
5-inch diameter Trim Ring mounts on the end of the self-supported duct.
(Not required, but the trim ring prevents sharp edges and/or unraveling and completes the look.)
7. Outdoor Air (Heat Exchanger) Plenum - 484350-1160
For Negative Pressure Rooms - When balanced airflow is required, attached the outdoor heat exchanger plenum with a 12-inch diameter duct from the side of the unit to an outside air source. The air to the outdoor heat exchanger is pulled from outside the room to eliminate problems associated with negative pressure. It attaches to the condenser intake side of the unit and is hinged for filter cleaning.
(Use with 12-inch Self-Supported Duct #8 or 12-inch Flexible Duct #10.)
8. Self-Supported Warm Air Duct / Negative Pressure Condenser Intake Air Duct - LA481744-0410
12-inch diameter Self-Supported Exhaust Duct extends up to 10-ft in length.
(Used as a warm air exhaust duct or intake duct with negative pressure air plenum.)
9. Ceiling Tile Exhaust Kit - HDK-12
MovinCool makes it easy to remove exhaust air. Simply replace your existing ceiling tile with the HDK-12 Ceiling Tile Exhause Kit. Place the Exhaust Flex Duct on top of the MovinCool unit and insert it into the specially cut ceiling tile.
Includes 1) 2-ft x 2-ft Ceiling Tile with 8-ft of 12-inch diameter Flexible Exhaust Duct.
10. Flexible Duct – LAY45771-0060 (not pictured)
12-inch diameter x 8-ft Flexible Air Duct. Can be used in place of Self-Supported duct.
11. Condensate Pump 115V - 484789-0210
No need to bother with manually emptying the tanks. The condensate pump will remove the water automatically to any remote drain. Maximum lift – 17-ft. Includes 3/8-inch diameter x 20-ft length drainage hose + installation hardware.
12. Storage Cover - LA484420-0840
Durable black nylon oxford unit storage cover.
